$ 59 $ 49

Ti-Pitch will create create impressive amounts of illumination underneath your pitch adjuster.

9 in stock

SKU: TiP Category:



Ti-Pitch kit includes the following:

  1. 2 Pitch PCB’s.
  2. Power supply (input = 110vac – 240vac output = 5v@.5A) ..
  3. Power Wire, Fused Connector.
  4. 1 Year Parts warranty.
  5. Lifetime product support via forums.

Ti-Pitch kit includes the following:

  1. 2 Ti-Pitch PCB units
  2. Power Supply.
  3. Connectors.
  4. 1 Year warranty Parts and Labor.
  5. Lifetime product support via forums.

This kit is for 2 turntables!

Ti-Pitch uses Super Bright 1210 SMD (Surface Mount Diode) to create impressive amounts of illumination in a small space.Ti-Pitch mounts on the top plate that screws onto the fader. It’s very easy to install onto the original screw points.

Supplied with complete installation technical build instructions..
Tools needed for install is a medium Philips screwdriver.
This is a DIY Kit that you must assemble & solder yourself.

Any kits that are not labeled “Premium Services” are all Do It Yourself *DIY & does not come with LED’s.

Be sure to check out our full line of “The ILLUMINATOR” products!
Now Shipping From Canada!

Additional information

Weight 1.0 kg
Dimensions 4 × 4 × 4 in

Installation Instructions

Ti-Pitch Kit Instructions:

*WARNING* DO NOT attempt to fit this kit with the unit plugged into the mains supply. Working on a live chassis is extremely dangerous and can cause damage to the appliance, personal injury or death!

Medium + Screwdriver
Small – Screwdriver


1) Unplug the power plug
2) Remove platter and 45 adaptor, if the platter sticks apply equal lifting force to the two holes and have someone tap the spindle lightly to release
3) With the lid fitted turn the unit upside down & DO NOT REST THE DECK ON THE ARM!
4) Remove the feet by turning counter-clockwise and remove the four screws underneath
5) Remove the 6 screws outside the platter circle
6) Remove the 11 screws from inside the platter circle

Fitting The Light Strip

1) Remove the knob and felt from the pitch slider
2) Remove the 5 platter cover screws and lift off the cover
3) Unplug the pitch control cable
4) With the lid fitted turn the unit upside down & DO NOT REST THE DECK ON THE ARM!
5) Remove the rubber base
6) Remove the 2 screws holding the pitch unit to the chassis and carefully pull the cable through
7) Remove the top plate screws from the pitch slider
10) Screw in the new board
11) Check the board is fitted straight and that the fader can move without rubbing or snagging on the board
12) Wrap the cables underneath and cable tie to the cable loom at each end
13) Run the cable loom back through the hole and reconnect the cable loom to the socket
14) Refit the fader assembly using the two screws, remember to connect the ground tag.


Use PART A steps 1-5 in reverse to reassemble


Plug in and switch on the turntable and ENJOY!




This kit is supplied only as an optional modification and users should be aware that fitting the modification is likely to invalidate any warranty with Technics-Panasonic. These instructions are supplied to assist in the installation of the included components and the supplier/manufacturer accepts no responsibility for damage to equipment or property and injury or death caused by incorrect installation and/or use of these instructions and it’s included components.


Compatibility Chart

Compatible Types

  • SL-1200MK2 & SL-1210MK2
  • SL-1200MK3 & SL-1210MK3
  • SL-1200M3D & SL-1210M3D
  • SL-1200MK4 & SL-1210MK4
  • SL-1200MK5 & SL-1210MK5
  • SL-1200MK5G* & SL-1210MK5G*
  • SL-1200MK5GLD* & SL-1210MK5GLD*
  • SL-1200LTD
  • SL-1210MK2PK
 (“*” indicates may require additional modification to the turntable)

Available Colors

UV Purple
Custom color configurations are available!


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.